CCFBG http://www.ccfbg.com/forum/ |
|
Barrie area chassis shop projects past http://www.ccfbg.com/forum/viewtopic.php?f=41&t=13495 |
Page 1 of 2 |
Author: | skinny z [ Sun Mar 18, 2012 4:09 pm ] |
Post subject: | Barrie area chassis shop projects past |
I thought I'd post up a few pics of the work we do at the small chassis shop I've been managing the last little while. We can offer a pick up and delivery service within a couple of hours from Toronto. 3rd gen 6 point cage with swing out side bars. |
Author: | skinny z [ Sun Mar 18, 2012 4:10 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Few more pictures... Another 3rd gen. This one a back half car. (FYI: The patches on the quarter panel are for the elongated wheel opening.) |
Author: | skinny z [ Sun Mar 18, 2012 4:11 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
..and a couple more. 1st gen Camaro that was one of our back half cars, then a full front sub frame was added. |
Author: | lb9 GTA [ Sun Mar 18, 2012 7:05 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Any finished pics of the tubbed 3rd gen? |
Author: | skinny z [ Sun Mar 18, 2012 8:32 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Here are a few more... |
Author: | 6SIX6 [ Sun Mar 18, 2012 9:50 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
just curious at what did the 6point cost for the 3rd gen you guys built as Im looking to do one at the end of the season. Thanks |
Author: | skinny z [ Mon Mar 19, 2012 6:15 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
PM sent. |
Author: | Daz [ Tue Mar 20, 2012 5:52 am ] |
Post subject: | Re: Barrie area chassis shop projects past |
Interested the same as Ray but going on a convertible.Swing out etc.. |
Author: | skinny z [ Tue Mar 20, 2012 8:16 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
PM sent. |
Author: | Mr Bastard [ Wed Mar 21, 2012 12:00 am ] |
Post subject: | Re: Barrie area chassis shop projects past |
those are some nice projects! |
Author: | skinny z [ Wed Mar 21, 2012 5:52 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Mr Bastard wrote: those are some nice projects! I'll post up some of the nostalgia gassers the shop has cranked out in the last couple of gears. That stuff is wild. Check out this vid of the "Hemi-J". 8 second alcohol injected blown hemi in a "street car" chassis. Mild steel at more than 3000 lbs. http://www.youtube.com/watch?v=nmgwmtkAc4M http://www.youtube.com/watch?v=GhYuszomJyE The Hemi-J is in the far lane. |
Author: | skinny z [ Wed Mar 21, 2012 5:54 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Here's another shot of the 3rd gen roll cage with swing outs. Access to the back seat is not unreasonable (anymore than it already is at least). |
Author: | skinny z [ Sat Mar 24, 2012 11:11 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
We can build some pretty interesting exhaust systems too. Here's a look at the modified Hedman headers and stainless y-pipe built for my project. The crossmember has been notched and reinforced to provide as much clearence as possible. It started out on the rusty chassis seen in the development pictures here and eventually ended up on my current chassis. Purge welded TIG on stainless. |
Author: | skinny z [ Sat Mar 24, 2012 11:13 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Stainless Y-Pipe and crossmember. |
Author: | skinny z [ Sat Mar 24, 2012 11:16 pm ] |
Post subject: | Re: Barrie area chassis shop projects past |
Few more... |
Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |