Author |
Message |
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Barrie area chassis shop projects past
I thought I'd post up a few pics of the work we do at the small chassis shop I've been managing the last little while. We can offer a pick up and delivery service within a couple of hours from Toronto. 3rd gen 6 point cage with swing out side bars.
_________________ 86 Sport Coupe.
Last edited by skinny z on Sun Apr 22, 2012 9:41 am, edited 2 times in total.
|
Sun Mar 18, 2012 4:09 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
Few more pictures... Another 3rd gen. This one a back half car. (FYI: The patches on the quarter panel are for the elongated wheel opening.)
_________________ 86 Sport Coupe.
Last edited by skinny z on Sun Apr 22, 2012 9:42 am, edited 3 times in total.
|
Sun Mar 18, 2012 4:10 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
..and a couple more. 1st gen Camaro that was one of our back half cars, then a full front sub frame was added.
_________________ 86 Sport Coupe.
Last edited by skinny z on Sun Apr 22, 2012 9:43 am, edited 1 time in total.
|
Sun Mar 18, 2012 4:11 pm |
|
|
lb9 GTA
CCFBG Club Member
Joined: Fri Apr 11, 2008 9:57 pm Posts: 823 Location: scarborough/markham
|
Re: Barrie area chassis shop projects past
Any finished pics of the tubbed 3rd gen?
_________________ 1988 Trans Am GTA, LB9, 700R4, CAI, cat back, SFCs, Pro Kit springs, wonderbar, LCRBs
|
Sun Mar 18, 2012 7:05 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
_________________ 86 Sport Coupe.
Last edited by skinny z on Sun Apr 22, 2012 9:44 am, edited 1 time in total.
|
Sun Mar 18, 2012 8:32 pm |
|
|
6SIX6
CCFBG Club Member
Joined: Thu Jul 05, 2007 5:32 am Posts: 1508 Location: Miserysauga , Ontario
|
Re: Barrie area chassis shop projects past
just curious at what did the 6point cost for the 3rd gen you guys built as Im looking to do one at the end of the season. Thanks
_________________My FQuickMy GarageTHE MISSISSAUGA CHAPTER
|
Sun Mar 18, 2012 9:50 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
PM sent.
_________________ 86 Sport Coupe.
|
Mon Mar 19, 2012 6:15 pm |
|
|
Daz
CCFBG Club Member
Joined: Sat Mar 19, 2005 8:15 am Posts: 3233 Location: Mississauga
|
Re: Barrie area chassis shop projects past
Interested the same as Ray but going on a convertible.Swing out etc..
|
Tue Mar 20, 2012 5:52 am |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
PM sent.
_________________ 86 Sport Coupe.
|
Tue Mar 20, 2012 8:16 pm |
|
|
Mr Bastard
CCFBG Club Member
Joined: Sat Mar 19, 2005 8:07 pm Posts: 4327 Location: The big town
|
Re: Barrie area chassis shop projects past
those are some nice projects!
_________________9.06@155 mph, small block pump gas with 3.42's bird 8.14@166 mph, big block on 250 shot monza
|
Wed Mar 21, 2012 12:00 am |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
Mr Bastard wrote: those are some nice projects! I'll post up some of the nostalgia gassers the shop has cranked out in the last couple of gears. That stuff is wild. Check out this vid of the "Hemi-J". 8 second alcohol injected blown hemi in a "street car" chassis. Mild steel at more than 3000 lbs. http://www.youtube.com/watch?v=nmgwmtkAc4Mhttp://www.youtube.com/watch?v=GhYuszomJyEThe Hemi-J is in the far lane.
_________________ 86 Sport Coupe.
|
Wed Mar 21, 2012 5:52 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
Here's another shot of the 3rd gen roll cage with swing outs. Access to the back seat is not unreasonable (anymore than it already is at least).
_________________ 86 Sport Coupe.
Last edited by skinny z on Sun Apr 22, 2012 9:45 am, edited 1 time in total.
|
Wed Mar 21, 2012 5:54 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
We can build some pretty interesting exhaust systems too. Here's a look at the modified Hedman headers and stainless y-pipe built for my project. The crossmember has been notched and reinforced to provide as much clearence as possible. It started out on the rusty chassis seen in the development pictures here and eventually ended up on my current chassis. Purge welded TIG on stainless.
_________________ 86 Sport Coupe.
Last edited by skinny z on Sat Mar 24, 2012 11:18 pm, edited 2 times in total.
|
Sat Mar 24, 2012 11:11 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
_________________ 86 Sport Coupe.
|
Sat Mar 24, 2012 11:13 pm |
|
|
skinny z
CCFBG Club Member
Joined: Sun Sep 26, 2010 8:24 am Posts: 342 Location: 400 Northbound
|
Re: Barrie area chassis shop projects past
Few more...
_________________ 86 Sport Coupe.
|
Sat Mar 24, 2012 11:16 pm |
|
|
|